Mini Lathe DIY Autofeed stop - Part 2

The bracket finally arrived for the auto-feed stop. A friend at work had it done for me, he uses a firm that uses high pressure water jets to cut aluminium, I gave him a 2D CAD file of the shape and they cut it out of a 20mm thick piece of Aluminium using water!

As is normal, for me at least, there were a couple of things that didn't quite fit, the top of the middle upright clashed with the gear for the cross slide travel so I removed 10mm from the top and then the front edge clashed with the back of the half nuts so I made it 5mm thinner.

Original design with material removed

Bracket Clearance

It was apparent that I wouldn't be able to put a securing bolt through the front of the bracket as there was just no clearance from the leadscrew so I drilled and tapped from the rear, you need to put the spanner through the gap in the bed but it works fine and will be less fiddly to tighten once I shorten the bolt.

Access through the bed to tighten the bolt

So, once I got it fitted to the lathe and tightened up it was time to see if it actually worked.

Side view

Front view

I engaged the auto-feed and it slowly moved along and when the lever hit the bracket it disengaged the auto-feed.

Success, it needs a bit more work and tidying up, I want to shape the lever and line it up a bit better and add a long M6 bolt in the hole in the bracket to give me some fine adjustment.

I'm also thinking about adding a spring and a latch mechanism which will fully disengage the lever when it's tripped as it currently stops the auto feed but doesn't fully reset the lever position.

I hope to test it out later with a thread I want to cut, if everything works out I will have succeeded in adding auto feed stop to the lathe with minimal modifications to the lathe itself.

If anyone wants the 3D model I can make it public on tinkercad.com, just ask in the comments.

Threading Gears - Calculator

Whilst trawling around the net I came across a really useful utility on a Blog written by lathnovice.
Where this utility varied from the others I found was that it came at the problem from the other direction, instead of entering your gear configuration and seeing what the TPI or pitch was you could enter your gears and the pitch or TPI and it then calculated the gears you needed, the position they should go in and even the error in the pitch if you were trying to cut imperial threads on a metric leadscrew.

I purchased one of the 63 tooth gears from arceurotrade hoping to cut imperial threads on my metric lathe and this utility proves that it can be done and the error in dimensions is less than with the standard gears.

Link

And, as usual, I thought to myself "that would really be useful as an app on my phone"

So after looking at the source code and scratching my head for a while I thought the easiest way would be to use Appinventor and create an app that just displays the code in a Web viewer so you can use it off-line.
I reduced the number of gears available and moved some of the info around so it would better fit on a phone screen.

I've checked with the creator and he's happy with this so here are some links.

The source on Appinventor Community Gallery here

The APK file here

Second thing - DIY Digital DRO

One of the important things about using the lathe is keeping track of how much material you're taking off, once removed it's very difficult to put it back on....

Don't forget to divide the amount you want to remove from the diameter by 2 as you are removing material from both sides .... sort of.
Using the dial on the slide is OK but I've seen lathes with digital readouts, how much are those I wonder?
After some research I found  a really good alternative to the standard slides and readouts available from the usual suppliers, I found a DIY version for around a fiver (£5) plus a bit of DIY.

DIY lathe DRO 1

DIY lathe DRO 2

It's based on this digital LCD tyre depth gauge off ebay.  It's basically a variant of the digital vernier but without the sharp pointy bits.

I attached mine on the cross slide by mounting a piece of steel plate using the travelling steady mounting holes (at least I think they are for the travelling steady) this then allowed me to use a magnet to stick the body of the gauge to, the end of the plunger has a magnet glues to it so that it will stick to the cross slide.  It could also be stuck on the lathe bed and measure the saddle travel.

My DIY DRO attached to the lathe

The plunger magnets are basically 2 very small neodymium magnets glued inside a small mild steel tube (turned on the lathe 7mmx4mm with a 2mm hole but these dimensions can be what you need) glued on the end of the plunger.

One of the problems with the mini lathe is actually finding space to mount the gauge as there's not a lot of room.

What I like to do is touch the tool to the material to be cut and set the DRO to '000' then move to tool to the right and move in the tool until I've reached half the amount I need to remove then reset the DRO to '0.00' and then turn down the material until I reach the '0.00' point and that's that.
So far I've found it quite accurate but noticed that it gets covered in swarf when in use, I thought about forming a piece of thin perspex to curve round the gauge and protect it from chips but then found an empty rectangular packet in the recycling bin that was about the size of the gauge but made of clear plastic, thin but strong enough to keep it's shape, this slid over the gauge and protected it completely and was flexible enough to still be able to press the buttons.

DIY DRO with plastic cover

It's also possible to connect to these gauges and get a serial data stream that could be read by an Arduino and shown on a larger LCD and there is a project out there that uses a Bluetooth interface to display the data on your smart phone here, one for my other blog maybe.

Comments/ideas/feedback welcomed.

First Thing

As I imagine most people do after buying a lathe nowadays, I also spent a lot of time watching YouTube videos.

One of my favourites is mrpete222 AKA Tubalcain, he's a retired teacher in the states who's done hundreds, if not 1000s, of videos on Milling, Turning and even casting aluminium parts, a definite must watch.

One of the little jobs he did made me think about doing the same thing for my little lathe, a knurled thumb screw to lock/release the measuring dial on the cross slide.
This replaces the supplied grub-screw and lets you set '0' on the dials as a deference point and then lock it in.

Grub-screw replaced by thumb-screw

Instead of turning the M6 thread from scratch though I cheated by using an M6 Bolt, all I did was shorten it and turn down the head so it was round and then I would have knurled the head ...if I had a knurling tool .. as I don't I just took my Dremel clone and put some cuts around the circumference of the head.

I also turned a small brass disc to put under the screw to protect the shaft from wear.

Assembly of parts

All in all it works pretty well but my next project meant that I don't often use the dials on the cross slide ... that's in the next post.

Which one, Where from?

So, once the decision was made to buy a lathe the next step was to research what was available within my budget and where would be best to get it from.

The second decision to be made was to buy new or second hand.

There are a few well known makes of lathes out there like Myford, Drummond etc. Myford lathes

Myford ML7 Lathe

seem to be one of the more common makes on the second hand market.
After looking through quite a lot of adverts for second hand lathes I decided that I didn't really have the experience needed to be able to look at a lathe and decide if it was OK or not and, even second hand, the cost was often more than the cost of a budget mini lathe.
Another thing to consider was the distance you may need to travel to pick up the lathe and don't forget, they are quite heavy.


Anyway, I decided to buy a new one and this would need to be an online purchase as there aren't any suppliers anywhere close to me.

Based on my web research it looks like the main contenders in the budget lathe market come from China made by a company called SIEG.  There are 3 main spec's of lathe, C1, C2 and C3, the C3 being the best spec.

These lathes are sold in the UK by distributors and there also some customised versions badged as their own brand.

The cost varies between £350 - £600 for one of the mini lathes, here are some of the places I looked.
www.arceurotrade.co.uk
www.warco.co.uk
www.axminster.co.uk
www.ebay.co.uk

The one I went for

I eventually bought mine from Warco.co.uk, (link) mainly because it came with a slightly better spec. than some of the others and also the price included courier delivery.

Having had the lathe for a few months I did come across a few quality issues that needed addressing and this is where I found out what a good company Warco was to deal with.
Whenever I had an issue with anything Warco always had someone ring me back to discuss the issue and then sent out new parts straight away, this was quite a pleasant surprise because my experience in dealing with most companies, when things go wrong, is usually a nightmare.

I will be going over some of the issues and solutions in later posts.

The First Entry

Having had a blog for my interest in electronics and the Arduino open source project for some time I decided to start a new blog to share my experiences with my new lathe, purchased in 2014, rather that confuse my existing blog.

Let's get one thing out in the open at the very beginning, I'm not an expert tool maker or an experienced hobby engineer I'm an electronics engineer with an interest in making things and a lathe is now part of my toolbox.

There is already quite a lot of information out there for lathes but most of it seems to be for larger/ older  lathes, way over my budget and probably too big to fit in my garage.

What I'd like to do is create some entries describing the process of how I went about buying a budget lathe and then moving on to the things I learned from reading other peoples blogs and many visits to YouTube which helped me improve both my lathe and my understanding of the lathe.

As you may be aware from reading my other blog, I'm not a prolific blogger and there may be quite some time between blogs.......